McIntosh mc 50 Bedienungshandbuch PDF herunterladen (Seite 4)

Data Port Connectors

The C50 Data Out Ports send

Remote Control Signals to

Source Components. A 1/8 inch

stereo mini phone plug is used

for connection.

General Information and Connector Information

Connector and Cable Information

XLR Connectors

Below is the Pin configuration for the XLR Balanced

Input and Output Connectors on the C50. Refer to the

diagrams for connections:

PIN 1: Shield/Ground

PIN 2: + Output

PIN 3: - Output

Power Control and Trigger Connectors

The C50 Power Control Out, Trigger and Pass-Thru

Output Jacks send Power On/

Off Signals (+12 volt/0 volt)

when connected to other

McIntosh Components. An

additional connection is for

controlling the illumination of

the Power Output Meters on

McIntosh Power Amplifiers.

A 1/8 inch stereo mini phone plug is used for con-

nection to the Power Control, Trigger and Pass-Thru

Outputs on the C50.

Note: The Power Control, Trigger, Pass-Thru and Data

Connecting Cable is available from the McIntosh

Parts Department:

Power Control, Trigger, Pass-Thru and Data

Cable Part No. 170-202

Six foot, shielded 2 conductor, with 1/8 inch stereo

mini phone plugs on each end.

Data

Signal

N/C

Data

Ground

PIN 2 PIN 1

PIN 3

PIN 1

PIN 2

PIN 3

1. For additional connection information, refer to the

owner’s manual(s) for any component(s) connected

to the C50 Audio Preamplifier.

2. The Main AC Power going to the C50 and any

other McIntosh Component(s) should not be applied

until all the system components are connected

together. Failure to do so could result in malfunc-

tioning of some or all of the system’s normal opera-

tions. When the C50 and other McIntosh Compo-

nents are in their Standby Power Off Mode, the

Microprocessor’s Circuitry inside each component

is active and communication is occurring between

them.

3. Balanced and Unbalanced Inputs and Outputs can

be mixed. For example, you may connect signal

sources to Unbalanced Inputs and send signals

from the Balanced Outputs. You can also use Bal-

anced and Unbalanced Outputs simultaneously,

connected to different Power Amplifiers.

4. The C50 internal Digital to Analog Converter

Circuitry is designed to decode 2-channel PCM

(Pulse Code Modulation) Digital Signal present at

the Coaxial and Optical Digital Audio Inputs. Other

Digital Audio Signal Format Types will cause the

Audio Outputs of the C50 to be muted and the Front

Panel Information Display will indicate an error

message.

5. The Remote Control Supplied with the C50 In-

tegrated Amplifier is capable of operating other

components. For additional information go to www.

mcintoshlabs.com.

6. When discarding the unit, comply with

local rules or regulations. Batteries should

never be thrown away or incinerated but

disposed of in accordance with the local

regulations concerning battery disposal.

General Information

Power

Control

Meter

Illumination

Control

Ground

Main, Output 1&2,

Trig 1&2

and Pass-Thru

7. For additional information on the C50 and other

McIntosh Products please visit the McIntosh Web

Site at www.mcintoshlabs.com.

1 2 3 4 5 6 7 8 9 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

McIntosh mc 50 Bedienungshandbuch Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zusätzliche Musikausrüstung McIntosh mc 50