McIntosh C500C Bedienungshandbuch PDF herunterladen (Seite 21)

Setup, con’t

3. Rotate the SELECT 1 Control until the desired Input

Title to be changed appears in the Display, e.g. “D

PORT CDR 5”. Refer to figure 29.

4. Rotate the SELECT 2 Control until the number 2 ap-

pears in the Display, e.g. “D PORT CDR 6”. Refer to

figure 30.

Note: Connect a 1/8 inch Stereo Mini “Y” adapter to

Data Port number 6 on the C500 Controller. From

each leg of the “Y” adapter connect a Cable to the

Data In jacks on each CD Player.

5. If there are any other Data Port re-assignments to be

made, repeat steps 3 and 4.

Note: DATA PORTS may also be switched off by

selecting “- -” using the SELECT 2 Control Refer

to figure 31.

6. If no other adjustments are to be made at this time,

press the SETUP Push-button to exit the Setup Preamp

Mode or proceed to the next desired Setup Preamp

Mode for adjustment.

Figure 30

Figure 29

Trim Level Adjustment

Various source components can have slightly different vol-

ume levels. This could result in the constant need to readjust

the C500 Volume Control when switching between different

Input Sources. The Level Input Trim Feature on the C500

Controller allows the adjustment of levels for each of the

Source Inputs, so that they have the same relative volume.

The Tuner and CD Inputs are used in the following ex-

ample.

Notes: The possible range of adjustment in volume level is

±6dB. The Tape/Record Output Levels are unaffected

by any changes in the Level Trim Settings. Any LEVEL

Trim adjustments made are retained in permanent

memory and can be changed only by performing a new

Level Trim Procedure. The Tuner Input Volume Level

can serve as a reference or choose another Input

Figure 31

Source that is frequently listened to as the reference.

The reference Input Source should be set to a Level of

00.

1. Rotate the SELECT 2 Control to select the Tuner Input

and adjust the VOLUME Control to the desired listen-

ing level. Refer to figure 32 .

Note: If the C500 Controller is in the SETUP Mode, exit

before proceeding.

2. Press the SETUP Push-button twice to access the Setup

Preamp Mode, unless the C500C is already in the Setup

Preamp Mode.

3. Rotate the MENU Control until the words “TRIM 0.0

TUN” appears. Refer to figure 33.

Note: The Level Input Trim can also be set via the

Remote Control.

4. If necessary, rotate the SELECT 2 Control until the

word TUN appears on the right side of the Front Panel

Alphanumeric Display, “TRIM 0.0 TUN”.

5. If necessary, rotate the SELECT 1 Control until two

zeros appears in the center of the Front Panel Alphanu-

meric Display, “TRIM 0.0 TUN”.

6. Rotate the SELECT 2 Control until the word CD ap-

pears on the right side of the Front Panel Alphanumeric

Display, “TRIM 0.0 CD”. Refer to figure 34.

7. Rotate the SELECT 1 Control until the Volume Level

of the CD Input is the same as the Tuner Volume Level.

Figure 35 indicates a 3.0dB decrease in the CD Level.

8. Rotate the SELECT 2 Control until the next desired In-

put Source Name is displayed.

9. Repeat steps 6, 7 and 8 until all the Inputs with sources

connected to the C500 have the same relative volume

levels when switching between them.

Figure 35

Figure 34

Figure 33

Figure 32

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

McIntosh C500C Bedienungshandbuch Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audioverstärker McIntosh C500C